Excellent spring seals factory manufacturer: Basics of fluid pump sealing – A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft. When sealing a centrifugal pump, the challenge is to allow a rotating shaft to enter the ‘wet’ area of the pump, without allowing large volumes of pressurized fluid to escape. To address this challenge there needs to be a seal between the shaft and the pump housing that can contain the pressure of the process being pumped and withstand the friction caused by the shaft rotating. The gap between the faces on a typical seal is as little as 1 micron – 75 times narrower than a human hair. Because the gap is so tiny, particles that would otherwise damage the seal faces are unable to enter, and the amount of liquid that leaks through this space is so small that it appears as vapor – around ½ a teaspoon a day on a typical application. Find additional info at https://www.dmsseals.com/scraper-seals.

What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself.

Although construction machinery looks extremely complex, the common characteristics that can be summarized are: Usually work outdoors. The work site often changes, and some can move by themselves. The working environment is usually dusty or stained. Nowadays, construction machinery generally adopts hydraulic transmission, because hydraulic transmission has the following obvious advantages compared with mechanical transmission: The power-to-volume ratio is large and the location arrangement is easy. It can realize stepless speed change. It is easy to realize overload protection. Less shock, vibration and noise.

It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.

It can maintain stable performance after prolonged exposure to various corrosive compounds. Due to its lack of polarity, low unsaturation, and high chemical stability, our gasket has high resistance to various polar chemicals such as alcohols, acids (acetic acid, hydrochloric acid, etc.), strong base (sodium hydroxide, oxidant, hydrogen peroxide), detergents, animal and vegetable oils, ketones and certain esters. It is designed to have excellent aging resistance and excellent resistance to compression set and compression stress relaxation. Therefore, our gasket has significant advantages over other conventional gaskets. Its excellent materials and manufacturing process enables it to achieve effective sealing when exposed to corrosive chemicals, friction, high temperatures or very low temperatures. At the same time, it is easy to install and has industry-leading creep resistance, which saves users a lot of time and cost and increases productivity.

Our piston seals are designed to provide excellent leak control. We guarantee that it can perfectly meet the user’s requirements for low friction, compactness, precise configuration and simple installation. It is designed for fluid power applications. It is made of compound materials with high performance, which guarantees excellent wear resistance and excellent extrusion resistance for the seal. It is designed to be suitable for almost all fluid media and is highly resistant to oxidation and corrosion. It has excellent dynamic and static sealing performance and can even work under dusty industrial environments. Moreover, it has strong adaptability to various working conditions and can adapt to a fast, high-pressure working environment. At the same time, it has unparalleled performance in extreme temperature environments.

Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.

DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Read more information on https://www.dmsseals.com/.

DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.